Following his post last week about the speed and scalability of your raster image processor, in this film, Martin Bailey, distinguished technologist at Global Graphics Software, explains how to determine how much raster image processor (RIP) power you need to drive a digital press by calculating the press data rate. It’s the best way of calculating how much RIP power you need in the Digital Front End (DFE) to drive it at engine speed and to ensure profitable printing.
If you’re building a digital press, or a digital front end (DFE) to drive a digital press, you want it to be as efficient and cost-effective as possible. As the trend towards printing short runs and personalization grows, especially in combination with increasing resolutions, more colorants and faster presses, the speed and scalability of the raster image processor (RIP) inside that DFE are key factors in determining profitability.
For your digital press to print at speed you’ll need to understand the amount of data that it requires, i.e. its data rate. In this film, Martin Bailey, distinguished technologist at Global Graphics Software, explains how different stages in data handling will need different data rates and how to integrate the appropriate number of RIP cores to generate that much data without inflating the bill of materials and DFE hardware.
Martin also explains that your next press may have a much higher data rate requirement than your current one.
Vast amounts of data can slow down your digital press resulting in wasted product or delayed delivery times.
In this post, Global Graphics Software’s product manager for Mako, David Stevenson, explores the challenge of printing large amounts of raster data and the options available to ensure that data doesn’t slow down your digital press:
The print market is increasingly moving to digital: digital printing offers many advantages over conventional printing, the most valuable of these is mass-produced, personalized output making every copy of the print different. At the same time digital presses are getting faster, wider, and printing at higher resolutions with extended gamut color becoming common place.
To drive the new class of digital presses, you need vast amounts of raster data every second. Traditional print software designed for non-digital workflows attempts to handle this vast amount of data by RIPping ahead, storing rasters to physical disks. However, the rate at which data is needed for the digital press causes disk-based workflows to rapidly hit the data rate boundary. This is the point where even state-of-the-art storage devices are simply too small and slow for the huge data rates required to keep the press running at full rated speed.
This is leading to a new generation of RIPs that ditch the disk and RIP print jobs on the fly directly to the press electronics. As well as driving much higher data rates, it also has the benefit of no wasted time RIPping ahead.
As you can imagine, RIPping directly to the press electronics presents some engineering challenges. For example, two print jobs may look identical before and after printing, but the way in which they have been made can cause them to RIP at very different rates. Additionally, your RIP of choice can have optimizations that make jobs constructed in certain ways to RIP faster or slower. This variability in print job and RIP time is a bit like playing a game of Russian roulette: if you lose the press will be starved of data causing wasted product or delivery delays.
With a RIP driving your press directly you need to have confidence that all jobs submitted can be printed at full speed. That means you need the performance of each print job and page to be predictable and you need to know what speed the press can be run at for a given combination of print Job, RIP and PC.
Knowing this, you may choose to slow down the press so that your RIP can keep up. Better still, keep the press running at full speed by streamlining the job with knowledge of optimizations that work well with your choice of RIP.
Or you could choose to return the print job to the generator with a report explaining what is causing it to run slowly. Armed with this information, the generator can rebuild the job, optimized for your chosen RIP.
Whatever you choose, you will need predictable print jobs to drive your press at the highest speed to maximize your digital press’s productivity.
Ever wondered what a raster image processor or RIP does? And what does RIPping a file mean? Read on to learn more about the phases of a RIP, the engine at the heart of your Digital Front End (DFE).
The RIP converts text and image data from many file formats including PDF, TIFF™ or JPEG into a format that a printing device such as an inkjet printhead, toner marking engine or laser platesetter can understand. The process of RIPping a job requires several steps to be performed in order, regardless of the page description language (such as PDF) that it’s submitted in. Even image file formats such as TIFF, JPEG or PNG usually need to be RIPped, to convert them into the correct color space, at the right resolution and with the right halftone screening for the press.
Interpreting: The file to be RIPped is read and decoded into an internal database of graphical elements that must be placed on the output. Each may be an image, a character of text (including font, size, color etc), a fill or stroke etc. This database is referred to as a display list.
Compositing: The display list is pre-processed to apply any live transparency that may be in the job. This phase is only required for any graphics in formats that support live transparency, such as PDF; it’s not required for PostScript language jobs or for TIFF and JPEG images because those cannot include live transparency.
Rendering: The display list is processed to convert every graphical element into the appropriate pattern of pixels to form the output raster. The term ‘rendering’ is sometimes used specifically for this part of the overall processing, and sometimes to describe the whole of the RIPing process.
Output: The raster produced by the rendering process is sent to the marking engine in the output device, whether it’s exposing a plate, a drum for marking with toner, an inkjet head or any other technology.
Sometimes this step is completely decoupled from the RIP, perhaps because plate images are stored as TIFF files and then sent to a CTP platesetter later, or because a near-line or off-line RIP is used for a digital press. In other environments the output stage is tightly coupled with rendering, and the output raster is kept in memory instead of writing it to disk to increase speed.
RIPping often includes a number of additional processes; in the Harlequin RIP® for example:
In-RIP imposition is performed during interpretation
Color management (Harlequin ColorPro®) and calibration are applied during interpretation or compositing, depending on configuration and job content
Screening can be applied during rendering. Alternatively it can be done after the Harlequin RIP has delivered unscreened raster data; this is valuable if screening is being applied using Global Graphics’ ScreenPro™ and PrintFlat™ technologies, for example.
A DFE for a high-speed press will typically be using multiple RIPs running in parallel to ensure that they can deliver data fast enough. File formats that can hold multiple pages in a single file, such as PDF, are split so that some pages go to each RIP, load-balancing to ensure that all RIPs are kept busy. For very large presses huge single pages or images may also be split into multiple tiles and those tiles sent to different RIPs to maximize throughput.
The raster image processor pipeline. The Harlequin RIP includes native interpretation of PostScript, EPS, DCS, TIFF, JPEG, PNG and BMP as well as PDF, PDF/X and PDF/VT, so whatever workflows your target market uses, it gives accurate and predictable image output time after time.
To find out more about the Harlequin RIP, download the latest brochure here.
If you’re in the process of choosing or building a digital front end for your press, you’ll need to consider how much RIPing power you need for the capabilities of the press and the kinds of jobs that will be run on it. The RIP converts text and image data from many file formats including PDF, TIFF™ or JPEG into a format that a printing device such as an inkjet printhead, toner marking engine or laser platesetter can understand. But how do you know what RIP is best for you and what solution can best deliver maximum throughout on your output device? This is the first of two posts by Global Graphics Software’s CTO, Martin Bailey, where he advises how to size a solution for a digital press using the data rate required on the output side.
Over the years at Global Graphics Software, we’ve found that the best guidance we can give to our OEM partners in sizing digital press systems based on our own solution, the Harlequin RIP®, comes from a relatively simple calculation of the data rate required on the output side. And now we’re making a tool to calculate those data rates available to you. All you need to do is to download it from the web and to open it in Excel.
You will, of course, also need the specifications of the press(es) that you want to calculate data rates for.
You can use the spreadsheet to calculate data rates based on pages per minute, web speed, sheets or square meters per minute or per hour, or on head frequency. Which is most appropriate for you depends on which market sector you’re selling your press into and where your focus is on the technical aspects of the press.
It calculates the data rate for delivering unscreened 8 bits per pixel (contone) rasters. This has proven to be a better metric for estimating RIP requirements than taking the bit depth of halftoned raster delivery into account. In practice Harlequin will run at about the same speed for 8-bit contone and for 1-bit halftone output because the extra work of halftoning is offset by the reduced volume of raster data to move around. Multi-level halftones delivered in 2-bit or 4-bit rasters take a little bit longer, but not enough to need to be considered here.
You can also use the sheet-fed calculation for conventional print platesetters if you so desire. You might find it eye-opening to compare data rate requirements for an offset or flexo platesetter with those for a typical digital press!
Fortunately, the latest version of the Harlequin RIP offers a framework that can help you to meet all these requirements. It offers a complete scale of solutions from a single RIP through multiple RIPs on a single server, up to multiple RIPs across multiple servers.
In my next post I’ll share how the data rate number can be used to make a first approximation of which class of RIP integration you should be considering.
The above is an excerpt from our latest white paper: Scalable performance with the Harlequin RIP®. Download the white paper here.
